Digital Shaking Incubator maintenance:

1 to accurately focus on equipment use and maintenance, it is in good working condition, extend equipment life.

2 instruments in continuous work, should be done once every three months regularly inspected; check fuses, control components and tighten the screws, and whether there are water droplets, dirt, etc. fall into the motor and control components.

3 transmission part of the bearing at the factory prior to filling the right amount of grease (1 Calcium - Kea), the instrument in continuous work, once every six months should bear grease, fill the bearing space volume of about 1 / 3.

4 period of the instrument is often used, natural wear and tear is normal. After a year in the use of the instrument, if one motor, compressor unusual noise; transmission parts bearing wear, belt loose or cracks, electrical component failure such as the failure of this enterprise will succeed to provide quality services to assist in handling.

5. Compressors should be avoided consecutive start.

Digital incubator maintenance:

1 daily observation incubator temperature compliance. Abnormal situation in a timely manner for a professional repair.

2 Lighting inside the timely replacement of abnormal lighting.

3 found that heating (cooling) when abnormal heating wire check (compressor) is damaged, damaged repaired in time.

4 time outside of health clean incubator, maintained clean clean. Weekly application of disinfectant for the incubator tank thoroughly cleaned once. Replacement of different varieties of each quarter of disinfectant to avoid drug-resistant species.

5 this year should be a performance verification equipment.

6 check carefully before using the device supply voltage requirements are consistent with the instrument.

7 equipment when not in use, set the control switch in a non-working state, cut off the power.

Digital light incubator care and maintenance:

1, the incubator enclosure should be grounded.

2 incubator to be placed in a cool, dry, ventilated area away from heat and sun areas. Stable place to prevent vibration of the noise.

3, to ensure efficient cooling condenser, the condenser should be larger than the distance between the wall 100mm, 50mm gap should be the side of the box, the box at the top of at least 300mm space.

4, incubator in the handling, maintenance, maintenance, avoid collisions, shake shake, the maximum gradient is less than 45 degrees.

5, the instrument suddenly not working, check the fuse tube (once the box) is burned out, check the power supply situation.

6, the incubator refrigeration work, not the inside temperature and the temperature difference is greater than 25 degrees.

7, the illumination time may be "programmable controller when the" self-programming, control the time. Programming, refer to "programmable controller when the" instructions for use.

Water-jacketed carbon dioxide incubator routine maintenance:

Since such devices are often exposed to water and gas, the gas of impurities may enter the gas pipeline, causing the machine does not work. Daily work required for maintenance from the following aspects: always check the water jacket of the water level, adding water if necessary to lower the water level; regular inspection of carbon dioxide gas cylinders, empty cylinders can not let carbon dioxide; check the carbon dioxide gas pipeline and a seamless interface to gas phenomenon; dust to the machine regularly to prevent dust from blocking the airway and solenoid valve.

Note for:

1, the initial use must be added sufficient deionized water or distilled water, covered with lids to reduce evaporation of water passed water.

2, instability in the power supply unit, equipped with high-performance voltage regulator for the best appliances to reduce the voltage instability caused by the fault.

3, install a low-pressure carbon dioxide cylinders 0 ~ 0.25Mpa carbon dioxide valve, the output air pressure more stable, so

4, can be avoided due to high pressure carbon dioxide input box. Carbon dioxide control valve is in working condition and long-term damage.

5, do not do training in case of power, temperature should be set to 00C, the carbon dioxide concentration at the end is set to "0", this would

6, so that they control valve is inactive, thus avoiding the control valve is in working condition and long-term damage.

7, the door to set the temperature higher than the inside temperature of 10C or so, to reduce access to items inside when the temperature fluctuations.

Shaking Incubator of maintenance:

1, apparatus in continuous work, done once every three months should be regularly checked; check fuses, control components and tighten the screws, and whether there are water droplets, dirt, etc. fall into the motor and control components.

2, the transmission part of the bearing at the factory prior to filling the right amount of grease, the instrument in continuous work, once every six months should bear grease, fill the space bearing account for about 1 / 3.

3, the compressor should be avoided consecutive start.

4, the instrument often used term, natural wear and tear is normal. After a year in the use of the instrument, if one motor, compressor unusual noise; transmission parts bearing wear, belt loose or cracks, electrical component failure such as the failure of the company will continue to provide quality services to assist in handling.